8/19/2023 0 Comments Sherwin williams rust color![]() However, it’s interesting and you can see what other colors are alongside it. It allows you to understand the paint color a bit more as in what color it may shift to or show in certain qualities of light.Īs for the color collections, Kilim Beige is a part of, this is certainly not crucial information. Knowing what hue family a color comes from is very beneficial. ![]() Kilim Beige comes from the yellow hue family, leaning towards the yellow-red hue family. You can expect it to reflect a decent amount of light. It’s almost right in the middle of the scale. To sum it up, Kilim Beige has an LRV of 57. A great article to read to learn more about LRV is Light Reflectance Value: What Do Those Numbers Mean? ![]() LRVs range from 0 -100, with 100 being pure white and 0 being absolute black. ![]() LRV or Light Reflectance Value is a measurement commonly used by design professionals that measures the amount of light reflected from and absorbed by a surface. Let’s start with LRV, What is it and why does it matter? Color Collections: Living Well, Top 50 Colors.Hue Family: Yellow, leaning towards yellow-red.Any help and information would be greatly appreciated.CLICK HERE TO GET A SAMPLIZE SAMPLE OF KILIM BEIGE STATS (I have spent about 60 hours on prep removing the old finish and wire brushing and sanding the pole.) In the process of stripping and preping I have noticed many infected areas ranging from extreme rust to areas where there is no zinc remaining with several transitions to bare steel. I'm curious about the causes of the white rust and if all my prep work will pay off with no recurring problems. Will this adhere to the Rust Destroyer OK or should I go with a solvent based color top coat? The recent weather has been fine with no rain and the initial coat of Rust Destroyer looks as if it is curing just fine.ĭo you have experience and information on the white rust issue I'm experiencing. Sher Cryl is water based and I read in your instructions to wait 72 hours before top coating with latex. Would you recommend ( or would it be O.K.) applying another coat for added insurance and if so how much time between coats do you recommend? Also I would like to apply the same SherCryl top color coats (2) as before. Based on information on the Rust Destroyer label at 75 square feet coverage per quart I think the film thickness should be the recommended 3 mils or maybe about 3.5 mils. The surface area of the pole is about 117 square feet. I learned of Rust Destroyer from a professional painter and applied about 1.8 quarts with a small roller to the freshly prepared pole this past saturday. The pole was stripped once again to bare metal. All the Sherwin Williams products used were water based. The day I painted did allow a full 6 hours of sunshine before sunset and the surface was dry to the touch. It was an extremely rainy month of December and there were only a couple of good days to paint so the spotty poor adhesion may have caused by the humidity/rainy weather. The pole was painted with Sher Cryl and there were many areas where the primer did not adhere well to the poles' surface. (A storage situation I noticed during the purchase process).Īfter stripping they recommended repriming with their Sher Cryl primer (water based) and finishing with the color top coat as before. Sherwin Williams suggested that the white rust condition may have been caused by improper storage of the pole on the wet ground. The report came back and the corrosion was identified as "white rust". Samples of the rust and corrosion were sent to Sherwin Williams lab for analysis. The pole was lowered and all the epoxy and paint was stripped and the rusty areas as well as the entire pole was wire brushed to clean bare metal. ![]() The pole was heavily galvanized and was painted originally with 2 coats of Sherwin Williams Macropoxy 646 and 2 coats of Sherwin Williams Sher-Cryl top color tinted finish coat.Īfter about 2 years the were many areas on most all sections of the pole that showed signs of rust forming under the 4 coats of epoxy primer and paint. The location is about 4 miles inland from the ocean and at 1200 foot elevation. I am in the process of trying to stop a rust problem on a 50 foot windmill pole located on the north end on the Big Island of Hawaii. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |